Bridge operating agencies

By the lifting mechanism, trolley run institutions and small frame components. Lifting mechanism includes a motor, brake, reducer, drum and pulley. Driven by motor through reducer rotating drum, wire rope wound on the reel or down from the roll to lift heavy loads. Small frame and mounting bracket is lifting mechanism and trolley run institutions and other parts of the rack, usually welded structure.
Bridge operating agencies
The metal structure of the bridge
From the main beam and side beams, divided into single girder and double girder bridge bridge categories. Single girder bridge by a single span girders and located on both sides of the end beam composed of two dual-beam bridge girders and by the end beam components. Main beam and side beams rigidly connected to the wheels at both Electric pallet jack with end beam for supporting the run on the elevated bridge. Main beam welded rails for lifting trolley. Bridge girder structure type more typical are:
1 box-shaped structure
(1) track box-shaped double beam is widely used in a basic form, the main beam from the upper and lower flange plates and sides of the vertical web composition, trolley rails arranged on the flange plate on the center line, and its simple structure, easy to manufacture, suitable for mass production, but the larger self.
(2) Partial rail box double side rail box girder and single girder cross-section are from the upper and lower flange plates and unequal thickness of primary and secondary webs composition, trolley rails arranged in the main webs top box Short body stiffener save where partial rail box girder by a single wide-flange box girder instead of two main beams, weight smaller, but more complex manufacturing.
2 four truss structure
The four combined into a closed space plane truss structure, the upper surface of the horizontal truss generally paved walkway plates, light weight, stiffness, but compared with other structures, size large, more complex manufacturing, fatigue strength is low, has been less production.

rotation angle

Fixed slewing jib crane can help you prepare and unproductive work shorten production time and reduce unnecessary waiting. Kellett company jib crane specification, all varieties, whether you are lifting weights, rotation angle, arm length and function of what kind of requirements, we can provide you with the best solution, even we have with dual spin arm, telescopic crane jib, etc.. All specifications have a common advantage: light weight, arm length, Scissor lift capacity, installation, operation and maintenance simple. They are completely independent, is an ideal job cranes, and applies to the outdoor yard and loading platform. Fixed column small footprint. Headroom for lifting very small case can get the maximum lifting heightbridge orbit at an elevated bridge crane, also known as crane. Bridge crane bridge laying on both sides along the elevated tracks run vertically, lifting trolley along the track laying sideways on the bridge, the scope of work constitutes a rectangle, you can take advantage of the space under the bridge lifting materials, not hampered by ground equipment. Such cranes are widely used in indoor and outdoor warehouses, factories, docks and open storage yard, etc.

easy to install

 good reliability, high stability KBK light crane components of the system are all standard modules can guarantee high-volume, high-quality production, which system is very reliable; system module is the mainstay of three sizes of rolled profiles, strength, stiffness, light weight, to ensure stability of the system.
2, KBK system adaptable plant powered palle ttruck station according to the needs, design and installation flexibility. Transported from the point to multi-point high accuracy, and more automated conveyor line beat, can be freely combined together. The plant can be used for new designs can also be used to modify or extend the old system.
3, easy to install, cost-effective KBK system installation is very convenient. KBK profiles between various standard modules can be used only with bolts, saving factory space and area, thereby reducing energy consumption, improve enterprise efficiency. System can be operated manually or can achieve automatic and semi-automatic operation.KPK-LS double girder overhead crane flexible standard components from the KPK, due to its lifting hoist is suspended between the two KPK main beam of the car frame, so double-girder suspension crane can offer higher than the single-beam crane lifting space

Construction crane industry once again restored in 2010 a rapid growth momentum.

First half of 2010, China's four major categories of construction crane sales totaled more than 24,000 units, an increase of 48.9%. In addition to exports, the major economic indicators are close to record levels during the first half of 2008. As of September 2010, China's only Hand pallet jacks cranes, truck-mounted cranes and crawler crane sales reached 33,712 units, more than 2009 full-year sales of 345 units 4 categories crane. Construction crane industry once again restored in 2010 a rapid growth momentum.
First half of 2010, exports of construction cranes rebounded, exports amounted to 1,133 units, exports amounted to 1.86 billion yuan, respectively, an increase of 43.6% and 40.0%. Among them, exports of 893 crane units, up 40.5 percent; crawler crane export 171 units, up 141.0 percent; crane export 96 units, down 6.8%.
From the first half of 2010 corporate sales situation, Xu Zhong, Zoomlion, Sany Automobile Lifting Machinery Co., Ltd. and other four companies Liugong truck cranes sold 17,463 units, accounting for truck cranes 87.15% of total sales, Xu Heavy sales growth biggest year growth rate of 30.5%; Sany Technology, XCMG Construction Machinery, ask dug Heavy and Zoomlion sold crawler cranes 736 units, accounting for this type of product total sales 91.43%, XCMG sales increase maximum , an increase of 115.8%; XU Sui
And total sales of Shijiazhuang Coal Mining Machinery crane 2370, accounting for the types of products 70.04% of total sales, Xu grew 62.4% over year.
Domestic construction crane on the market, cranes (including all terrain crane) is still the industry's leading products. January to September 2010, truck crane sales 27,572 units, up 35.6%; total exports of 879 units, an increase of 62.1%. Which ,3-June for the automotive crane sales season, the average monthly sales of 3,500 units or more, the peak appeared in March, sales reached 4,429 units; January largest growth rate, an increase of 158.3%; while sales in February and September appeared fell. From the product structure, small and medium-tonnage truck crane sales increased. 1344 crawler crane sales units, up 61.93 percent, close to the 2008 record high. Sales of products to 50t, 70t, 80t, 100t, 150t and 250t crawler crane mainly small and medium level. Truck crane half sales 4796 units, up 38.53 percent.

the technological level of domestic production and manufacturing capacity.

Currently, XCMG crawler crane 2000t level has also been unveiled, Zoomlion 3200t design and development is underway. Large tonnage crawler cranes, it not only makes our country to rid itself of this type of product is completely dependent on imports of the situation, but also fully demonstrates the technological level of domestic production and manufacturing capacity.
Construction crane industry industrial restructuring in the enterprise development strategy deepening. In 2006, Terex acquired 50% equity interest from long; 2008, Liugong acquisition Bengbu Vibro Engineering Machinery Co., Ltd. Jinzhou Huayuan Fuwa Heavy Machinery M & Co., Ltd., a joint venture Manitowoc Dongyue Heavy Industries and etc., are the development of the enterprise and a significant impact on the industry, and are fully reflected in 2009. In 2009, Anhui Liugong sales revenue grew 72.7%, cranes sales grew 62%; ask dug Heavy brocade truck crane 297 units sold, an increase of 234%; Hoisting Machinery Co., Ltd. Sany Automobile sales jumped cars Crane's first three production enterprises; Jingcheng Heavy Recovery truck crane machine production, when it achieved sales of 83 units of the good results. 2009, XCMG and Zoomlion Mobile Crane Branch 2 industry profits accounted for 95.5% of total profits.municipal and other areas of powered palle ttruck equipment needs of the crane diversified trend, greatly stimulated the crane, crawler cranes and other product development. In 2008, the market share of these two models, respectively, reached the highest value of 16.5% and 5.9%.

What principle pallet truck?

 pallet jacks is hydraulically powered energy, access to power pallet trucks. Pallet trucks are divided into: hand pallet truck (semi-braking), electric pallet truck (essentially full brake).
Pallet truck for heavy and long freight forwarding conditions, can greatly improve cargo handling efficiency, reduce labor intensity. But electric pallet truck is electric as the kinetic energy in the kinetic energy is exhausted, unfit super long hours.
Pallet trucks principle is: first tank of diesel oil into diesel filters, then pump, pump oil into the head, above the piston explosion constant motion of the piston, the power transmitted to the following spindle, then drive gear rotating flywheel has been reached, then the gearbox, drive gears inside, has been connected to the wheels, so move.

Truck forks: the whole stamping molding process, patented design of the anti-collision Beatles-type fork, strength increased by 25%, to ensure the normal use of the van in case of fork never deformation; fork surface using electrostatic spray, anti-wear, never fade; truck fork lift height generally about 200mm;
Truck fuel tank: truck with cast iron cylinder whole cast, external oiler design, this design extends the overall life of the cylinder truck. Van cylinder seals in the German original imported components, seals in the cylinder in the working life of 5,000 hours or more, to ensure van used in the three-year period without replacing seals. External oiler truck built with elastic rubber oil cup, working at low temperatures does not produce cavitation phenomenon.

Tiger Force four electrics tacker scissor lift platform product description:
1 heavy cut design
(2) the use of imported high-quality pump station, so goods lifting smooth and powerful
3 using pinch scissor design
4 mesa stripe beneath the aluminum safety profile, when dropped down an obstacle stops to ensure safety
5 internal power unit is equipped with a safety valve to prevent overload operation, flow control valves control the rate of decline
6 pivot point automatic lubrication design, long life
7 comply with the European EN1570 and USA ANSI / ASME safety standard
Tiger Force Foot motorcycle lift platform product description:
1. Designed for professional operation
2 By foot you can easily lift platform
3 overload valve and mechanical stop to ensure the safety of the operator. Mechanical stop to ensure the lifting or lowering platform can be stopped at any position, and the stability and security of the same.or unknown reasons, in front of a flatbed trailer brakes suddenly, named Ma too close too late to brake due to distance from the vehicle, he tried to fight the direction over trailer. Unexpectedly, an oncoming tanker. Panic, named Ma had to take chances through the middle from the two cars.

Tiger Force low-end platform trucks Products:

1 low type, minimum height 230mm
2 foot hydraulic pump station (Manual Series)
3 in line with European standards EN1570 and USA ASME safety standard (electric series) Tiger Force three electric scissor lift platform Product description:
1 Heavy-duty design.
(2) meet EU standard EN1570 and ANSI / ASME safety guidelines.
(3) European production of electric unit, reliable quality.
Standard safety features:
1 table with aluminum bottom crosspiece safety device, when the tops fall down to stop when an obstacle, to ensure safety.
2 internal power unit is equipped with a pressure relief valve to prevent overload, the flow control valve to control the rate of decline.
3 heavy duty fuel tank with drainage devices and check valves, pipes burst when the lift platform can be stopped declining.
4 using powered palle ttruck scissor design.
Other security measures:
1 in the pivot point with a self-lubricating bushings.
2 removable lifting operations and lifting eyes can help secure the lifting platform. Transported through ball table so that the workpiece is more time and more effort, more secure
You can lift the ball, the ball rises, the workpiece can easily push; ball down when the workpiece in contact with the table to ensure the safety during transportation BE electric platform trucks used by the U.S. Johnson Controls produces Varta (VARTA) maintenance-free start battery, saving maintenance time and cost, built-in charger, with power indicator, low voltage warning light
Suitable for packing production lines and conveyor machine shop products, molds, jigs, etc., can greatly reduce the labor intensity

You can lift the ball

With high-quality hydraulic pump station, powerful, maintenance-free battery, lasting power.Special rolling process manufacturing "C" type door frame, strong safety.Drum truck lightweight design of the structure is simple, easy to operate and effort.High quality cylinder, lifting speed, lifting height can reach 1450mm, electric 180-degree flip.With electronic weighing, there is zero, tare weighing function, accurate to 3/1000kg.
Used in chemical, food shop, dyes,pallet jacks, adhesives, oil, cooking oil and other liquid fluid handling, loading and unloading, pouring and other uses.
German VOLOX standard truck detail:
Rated load (kg) 600 Lifting height (mm) 145 Lower height (mm) 85 Overall width (mm) 420Is a department store, all kinds of small shops, pharmacy, pharmacies, offices, schools, hospitals and other places ideal for handling tools, as long as the handle is pulled back can easily drag the tray (use of leverage)
Tiger Force BT20 Type Ball mesa platform truck Products:
Transported through ball table so that the workpiece is more time and more effort, more secure
You can lift the ball, the ball rises, the workpiece can easily push; ball down when the workpiece in contact with the table to ensure the safety during transportation BE electric platform trucks used by the U.S. Johnson Controls produces Varta (VARTA) maintenance-free start battery, saving maintenance time and cost, built-in charger, with power indicator, low voltage warning light
Suitable for packing production lines and conveyor machine shop products, molds, jigs, etc., can greatly reduce the labor intensity

With high-quality hydraulic pump station,

With high-quality hydraulic pump station powerful, maintenance-free battery, lasting power.Special rolling process manufacturing "C" type door frame, strong safety.Drum truck lightweight design of the structure is simple, easy to operate and effort.High quality cylinder, lifting speed, lifting height can reach 1450mm, electric 180-degree flip.
With scissor pallet truck weighing, there is zero, tare weighing function, accurate to 3/1000kg.Used in chemical, food shop, dyes, paints, adhesives, oil, cooking oil and other liquid fluid handling, loading and unloading, pouring and other uses.
German VOLOX standard truck detail:
Rated load (kg) 600 Lifting height (mm) 145 Lower height (mm) 85 Overall width (mm) 420Is a department store, all kinds of small shops, pharmacy, pharmacies, offices, schools, hospitals and other places ideal for handling tools, as long as the handle is pulled back can easily drag the tray (use of leverage)Harbin -2011 excavator pallet truck
Harbin Engineering Machinery 20110 blue diesel vehicles can not pull 45-150 own mini excavator pallet truck, farm tractor, front and twin air brake, height 65-75 cm, the upper and lower flexiblPallet truck - Standard
The system is equipped with a number of hydraulic jacks; international CE safety standards Valves
First, the pressure relief valve: When the load exceeds the set maximum hydraulic system can help the oil output of the bypass flow back into the tank.
Second, the compensation control valve: pressure and flow changes via the control valve automatically granted with the rate of decline in order to protect the body, and cargo safety.
※ Low Bed 65m / m, and bed pads conform sided mechanical handling operations, and another double wheel design to overcome high loads and uneven ground dedicated and strong acid, water wheels of rust MC.

Multifunction electric drums car YL500B

Hydraulic truck precautions for useThe use of hydraulic truck note:
1 After the necessary training, and fully familiar with the hand pallet trucks and authorized operation, prohibit the operation of the hydraulic truck.
2 pay attention to check before operating the vehicle, with particular attention to check the wheels, handle assembly, the fork and the pendulum state.
3 Do not muddy, uneven ground using the van
4 Do not pallet jacks any part of your body's mechanical lifting of the vehicle near the site, on the goods under a fork
5 pallet trucks manned prohibited.
6 operator to bring the best gloves for protection.
7 Do not use the vehicle to carry the slack and tight goods shown sleepy
8 Do not overload pallet trucks
9 - Handling shelves, note the shelf forks placed on the center, not the goods placed on the rear shelf.
10 Only the weight of the goods even get on the shelf, the vehicle can be used to its maximum load.
11 Make sure the fork length greater than or equal the length of the pallet.
12 When not in use, place the fork to a minimum height.

To this end, named Ma will assume full responsibility for the accident, and was sentenced to a fine of 200 yuan. In addition, he will assume the other two drivers injured in car repairs and the cost of treatment.
In this, to remind you, and you must be careful driver master drive, or may cause incalculable damage

Flatbed truck brakes too late, into a "biscuit"

Jun Wei Ling Ying flatbed Reuters: at 11:40 on September 18 Xu, a tensile load of sand in ukwi medium dump truck rollover occurred connecting line scissor pallet truck Police mobilization crane at the site cleaned up more than five hours later, the road vehicle began to slow traffic.
Postponed fleet, named Ma driving flatbed pull loaders are carrying a road.
17 am, when the named Ma drive reaching ukwi cable 3588 km +350 m when, for unknown reasons, in front of a flatbed trailer brakes suddenly, named Ma too close too late to brake due to distance from the vehicle, he tried to fight the direction over trailer. Unexpectedly, an oncoming tanker. Panic, named Ma had to take chances through the middle from the two cars.
As models are large, three cars were stuck together unfortunately, could not move. Tanker drivers accident caused a broken left hand.
Wulabo highway traffic police brigade police told reporters: "There was no vehicle in front flatbed keep a safe distance between vehicles, in the former case of car parking, too late to take measures, resulting in two vehicles caught in the middle."
To this end, named Ma will assume full responsibility for the accident, and was sentenced to a fine of 200 yuan. In addition, he will assume the other two drivers injured in car repairs and the cost of treatment.
In this, to remind you, and you must be careful driver master drive, or may cause incalculable damage

Maintain Leak repair protection

Bridge crane trolley gear due to vibration, abrasion, pressure, temperature and other factors, the combination of surface sealing parts often appear static leakage. Traditional treatment methods to remove reducer, replacing gaskets or sealant applied, but time-consuming and difficult to ensure the sealing effect, will appear again in the operation of leakage. Contemporary Western countries use more polymer composites leakage field of governance, the most widely Blessed World Blue series. Polymer-free disassembly repair and materials have excellent adhesion, oil resistance and 350% elongation, good to overcome the impact of vibration reducer, repair effect is more effective than traditional methods.
Wear governance
Bridge crane initiative running gear wheels and carts frequently repeated emergency stop and parking will cause reverse gear torque of each axis, vibration increases, could easily lead to leakage. Such problems occur, the traditional method and more to be machined after welding or repair the main brush, but there are some drawbacks both: high thermal stress generated by welding can not be completely eliminated, prone to bend or break; the brush plated by the coating thickness limit is easily peeled off, and the above two methods are metal with metal repair, you can not change the "hard to hard" with the relationship, the combined effect of the force, will cause wear again. New repair method mostly polymer composites based, and the application of more surgery products, which has superior adhesion, electric pallet trucks compressive strength and other performance. Applied Polymer repaired, neither welding thermal stress on the repair thickness is not restricted, while products with metallic materials do not have the concession, can absorb shock and vibration equipment, to avoid the possibility of re-wear and greatly extended equipment component life, save a lot of down time, creating significant economic value.

Allowed to casually throwing things down from the car.

(14) limit switches and interlock protection device should always check.
(15) is not permitted to touch the limit switch as a parking solution.
(16) lifting the brake problem, you can not lift heavy objects.
(17) was Hand Pallet Truck objects are not allowed to run over the people or equipment.
(18) When welding unit of the crane, to specifically set the ground, do not allow the use of body ground.
(19) hooks in the lower limit position, the roll must retain the safety loops more turns.
(20) Cranes not collide with each other, but does not allow the use of a crane to push another crane to work.
(21) lifting heavy objects, liquid metal, explosive and dangerous goods, you must first slowly lifting from the ground 100 ~ 200mm, trial brake reliability.
(22) repair and inspection of the lighting, the voltage must be 36V or less.
(23) Overhead Crane all electrical equipment enclosure should be grounded. If the car is not welded to the main beam track should be taken when welding ground measures. Ground wire cross-sectional area greater than 75mm2 available galvanized flat iron or bare copper or greater than 10mm2 30mm2 galvanized round. Cab or crane body ground position should be more than two. Any point on the crane to the power between the neutral point grounding resistance should be less than 4Ω.
(24) to have regular safety technical inspection, good pre-preparatory work.

in order to produce high-end products, such as nuclear ring cranes, large weight

Crane manufacturing industry is closely related to urban construction, transportation, energy development and other people's livelihood cause of the industry. In recent years, China's crane industry has achieved rapid development. To bridge gantry crane manufacturing company, for example, to 2008, China's bridge gantry crane has about 450 manufacturing enterprises, employing over 14 million people [1]. If these enterprises are divided into three echelons: big play, too heavy in the first echelon, they are the industry's largest economy enterprises, with national technical center, comprehensive strength, in order to produce high-end products, such as nuclear ring cranes, large weight metallurgical cranes, foundry cranes, large dock cranes, etc.; second tier that includes Weihua Group, including China's top 20 companies, most of them have plant-level technology center, which is the establishment of Weihua Group regional technology center in Shanghai set up a product design and Research Institute, these enterprises are the backbone of the industry, products cover a wide range of high-end Pallet stackers both in bidding, also participated in the competition from cheap generic products; third echelon is the remaining four hundred SMEs, which generally are small, roughly the same product type, and to be priced competitively based market share effective strategies to enable these enterprises generally poor, severely hampered the pace of development
the inspection of the overhead traveling crane pulley. Focus on the bottom wear is excessive and cast iron pulleys for cracks. For institutions pulley overlooking Yang balance wheel, because it does not operate normal conditions, it is easily overlooked. So, be sure to check before installation flexibility of its rotation, otherwise, the installation length of rope around overlooking Yang and tension can not balance wheel to automatically adjust, so that an increase in the height adjustment overlooking Yang rope and operational risk level of difficulty.

Calm on the surface

Five forces competitive model with existing industry structure
An industry structure is composed of five competitive forces jointly determined. This five competitive forces are: enter threat threat of substitution, bargaining power customers, suppliers, price negotiation and competition among existing competitors. Let's analyze the existing competitive forces crane industry: First, enter the threats: For the current market, the threshold is low, new entrants into easier; Second, the threat of substitution: other lifting machinery pallet jacks due to its structure and use the occasion different, gantry crane is not a threat; Third, customer bargaining power: industry is still in a buyer's market, the customer's bargaining ability; four, supplier bargaining power: Because the client side is often specified parts, supply-side bargaining ability; five industry competitors: competitors include both well-known within the industry nationwide each crane manufacturers, local businesses, including the introduction of foreign technology, as well as direct access to the domestic foreign joint venture enterprise.
Through the above five force model analysis, we can conclude that: In the new round of competition, or will the winning companies should have such qualities: one, the introduction of advanced and mature technology and can quickly industrialization; two , R & D ability, high-tech products.
Calm on the surface, but the choppy water, today's market, in addition to great effect, too this two General Corporation and Weihua and some other companies in the second tier, and the remaining four hundred small and medium sized companies who have opportunity to forge a red, crossed the goal. And how to break loose, occupying a hill? This had lead to the topic of technology up.

the development of momentum is good,

Lifting machinery industry value chain downstream enterprises are mainly iron and steel industry, shipbuilding (shipbuilding) industry, machinery industry, stone industry and hydropower industry and other manufacturing industries. We can see that in the Hand pallet trucks industry, for example, a few years ago, the former provincial annual output from this about a million small and medium enterprises, but also a year to maintain production units 30,40, and now the industry's demand for lifting machinery has been basically saturated. For the development of SMEs, eyes in addition to continue to be on the traditional steel, shipbuilding, machinery processing and stone industries, but also to invest in other industries, such as thermal power industry, the industry has been the impact of national policies in recent years, the development of momentum is good, although the first two months of this year the overall loss of thermal power, but the appearance of state-led investment is very obvious, only two months, the government in power, heat production and supply industry's overall investment in fixed assets reached 63.1 billion yuan, an increase of 20.6%.
China's crane industry in the process of growing doomed smooth sailing, the economic crisis, in shock identify the future direction of development, need to learn a number of areas, the lack of need to improve a lot. Experienced orgasm, settling at the bottom, tortuous journey to build our industry grow and mature.

Product sales in the domestic construction cranes, truck cranes have been dominant

However, sales data 2006-2009, truck crane market share began to decline from 2007 to 80% in 2009 to 79.5%. With the development of economic construction, transportation, energy, metallurgy, petroleum, chemical, municipal and other areas of production equipment needs of the crane diversified trend, greatly stimulated the crane, crawler cranes and other product development. In 2008, the market share of these two models, respectively, reached the highest value of 16.5% and 5.9%.
Tonnage continuously improve product is nearly three years of construction cranes in a major trend, crawler crane is one of the fastest growing types of aircraft. In 2003, sales of crawler crane market is just Hand pallet trucks sets, and products are mainly small and medium-tonnage. Into the "Eleventh Five-Year", the large-scale integration lifting mode become the development direction of large tonnage crawler cranes rapid increase in demand, China's leading enterprises have started construction crane develop large-tonnage products. Beginning in 2009, Zoomlion, Sany, XCMG Fuwa Heavy Industry and launched a kiloton crawler cranes. Currently, XCMG crawler crane 2000t level has also been unveiled, Zoomlion 3200t design and development is underway. Large tonnage crawler cranes, it not only makes our country to rid itself of this type of product is completely dependent on imports of the situation, but also fully demonstrates the technological level of domestic production and manufacturing capacity.
Construction crane industry industrial restructuring in the enterprise development strategy deepening. In 2006, Terex acquired 50% equity interest from long; 2008, Liugong acquisition Bengbu Vibro Engineering Machinery Co., Ltd. Jinzhou Huayuan Fuwa Heavy Machinery M & Co., Ltd., a joint venture Manitowoc Dongyue Heavy Industries and etc., are the development of the enterprise and a significant impact on the industry, and are fully reflected in 2009. In 2009, Anhui Liugong sales revenue grew 72.7%, cranes sales grew 62%; ask dug Heavy brocade truck crane 297 units sold, an increase of 234%; Hoisting Machinery Co., Ltd. Sany Automobile sales jumped cars Crane's first three production enterprises; Jingcheng Heavy Recovery truck crane machine production, when it achieved sales of 83 units of the good results. 2009, XCMG and Zoomlion Mobile Crane Branch 2 industry profits accounted for 95.5% of total profits.

Gantry crane lifting capacity of up to 2000 kg

 all uses Suspension cranes impossible or uneconomic place can be easy to use. Gantry cranes can be easily split into several easy to transport parts used in another place and can Electric pallet truck assembled, this feature has benefits on many occasions. Trackless beam gantry crane lifting capacity of up to 2000 kg.

Pilasters jib crane Its biggest advantage

 is that it can be mounted directly on the wall or column, or it can be installed in machinery and equipment, thus do not take up any floor space.
Pilasters jib crane Its biggest forklift jacks is that it can be mounted directly on the wall or column, or it can be installed in machinery and equipment, thus do not take up any floor space.

Gantry crane lifting capacity of up to 2000 kg,

 all uses Suspension cranes impossible or uneconomic place can be electric pallet trucks to use. Gantry cranes can be easily split into several easy to transport parts used in another place and can quickly assembled, this feature has benefits on many occasions. Trackless beam gantry crane lifting capacity of up to 2000 kg.

Fixed slewing jib crane can help you prepare and unproductive work shorten

 time and reduce unnecessary waiting. Kellett company jib crane specification, all varieties, whether you are lifting weights, rotation angle, arm length and function of what kind of requirements, we can provide you with the best solution, Electric pallet jack we have with dual spin arm, telescopic crane jib, etc.. All specifications have a common advantage: light weight, arm length, lifting capacity, installation, operation and maintenance simple. They are completely independent, is an ideal job cranes, and applies to the outdoor yard and loading platform. Fixed column small footprint. Headroom for lifting very small case can get the maximum lifting height

KPK-LS double girder overhead crane flexible standard components from the KPK,

due to its lifting hoist is suspended between the two KPK main pallet jacks of the car frame, so double-girder suspension crane can offer higher than the single-beam crane lifting space

KBK flexible light combined system including KBK-D monorail crane,

KBK-LD single beam, KBK-LS double girder, KBK-LSS telescopic beam, KBK-LM stacker and other various types of lifting equipment, lifting weight of 0.125t -1t adapt to a very wide range, electrics tacker for modern production conveyor line, which features are summarized below:
1, good reliability, high stability KBK light crane components of the system are all standard modules can guarantee high-volume, high-quality production, which system is very reliable; system module is the mainstay of three sizes of rolled profiles, strength, stiffness, light weight, to ensure stability of the system.
2, KBK system adaptable plant each station according to the needs, design and installation flexibility. Transported from the point to multi-point high accuracy, and more automated conveyor line beat, can be freely combined together. The plant can be used for new designs can also be used to modify or extend the old system.
3, easy to install, cost-effective KBK system installation is very convenient. KBK profiles between various standard modules can be used only with bolts, saving factory space and area, thereby reducing energy consumption, improve enterprise efficiency. System can be operated manually or can achieve automatic and semi-automatic operation.